A long needed update

Well things have been a bit manic recently so updates were last thing on the mind.

But alas here we are April 2015 and here is an update on how things are going.

Ian’s Car – 200tdi 90

Well 12 months since the rebuild finished, its MOT time again.  Car went in for its test Tuesday 7th April.  It failed 😦  The issues were headlights weren’t bright enough, the drivers door wouldn’t open from inside the car.

So all in all not too bad, but the worst item was down as an advisory but actually caused the end of the test.  A UJ in the rear prop had failed to the point where the tester wasn’t willing to carry out deceleration tests.  The prop was unbolted and the UJ’s purchased and replaced.  the prop then bolted back on and boy did it make a difference.

The door not opening was a case of adjustments on the mechanism for the handles just shortened them a bit and opening now much easier.

The headlights were the biggest concern.  As I have high performance bulbs fitted to the car when the tester said they didn’t register on the testing machine.  So reading around the subject points at a burnt out light switch causing poor performance.  The solution is to put a relay feed to the lights.  I purchased a Red Bison Boomslang from Paddockspares for £30 it was a bargain for the entire kit.  I had it fitted in no time and made a massive improvement, its a product I would recommend to anyone.

MOT Retest 18 April 1pm.  Result: Car passed

Jordan’s Series II

Well not much work has been done on the car since November, panels are now painted but not yet fitted to the car.  The accelerator has now been refitted and the car can be driven around.

The main reasons for this is we have been busy working on Jordan’s Discovery 2, which since november has had a number of coolant hoses as it has been loosing coolant and the pressure build up has popped them.  We have now replaced the suspected cause of the coolant loss and so far so good.

Nick’s Discovery

It has been plodding along as normal.  We had a bit of fun while jet washing it ready for MOT when the jet wash smashed the sun roof.  so that has been replaced and the alpine windows have been taken out and covered over.

Matthews Series.

As Matthew has decided he isn’t friends with 2 / 3 of us working on Land Rovers there will be no further updates about his car as we dont see him any more.

New Cars:

Yes we have been joined by two more land rovers that we can enjoy working on.

Daisy The Defender is a 2006 TD5 90, owned by some friends we have had a little bit of work to do on the car already including replacing a failed fuel pump and then adding some new bits such as chequer plate wing tops and a new bumper.  With being such a new car there shouldnt be that much to do on it for now.

Tom’s 300tdi 90, this is going to be our next big project, Toms car is in need of a new chassis, due to the amount of rust it has, we could go down the route of repair pieces but Tom fancies doing a chassis, so one has been ordered so big project ahead for the summer.  There should be plenty of updates on this one.

Advertisements

Car 4 : Matthew’s car finished

Well after a busy 8 months Matthews car has been finished and has passed its MOT.

The details of the rebuild have been missing during the process but hopefully we will make a post that covers all the bits we went through.

To celebrate we took the cars to the pub for a pint.

IMG_0695.JPG

IMG_0694.JPG

November Update

Well after being quiet for a while since we updated the site so here is where we are up to at the moment.  Pictures of the cars will follow soon.

Car 1 –

The last update showed the van sides and roof bolted in place.  Since then we have fixed the inner sills and seat box in place, offered up the floor panels for a fit.

We have also replaced the carb that was originally on the car as when it ran there was a terrible misfire, we now put this down to an assumption the rotor arm moved one direction where it actually went the other so the ignition was only right on 2 cylinders.

With the running sorted we have actually had a short drive around and the engine seems to run very nicely indeed.  Hopefully will add a video to show this soon.

The bonnet has now been rubbed down and ready to paint, with the wings to follow.

Car 2 –

Not much has happened for now with the car still gently running it in driving most days.  We ventured on a 2 hour drive out to Betws-Y-Coed to watch the Cambrian rally in the middle of October, on the way home the car cut out with a diesel leak, eventually we got it home.

On the Sunday after the cause turned out to be the Fuel lift pump, as we revved the engine a mist was seen coming out the bulkhead side.  This was replaced and has run fine since.

We also fitted a pair of Wipac 100w 8″ spot lamps on the front for helping with night time driving on the dark lanes in the area,

That was until today, where got in it this morning and it wouldn’t turn over. Not sure what the issue is at present but will be looking in to it.

Car 4 –

Well progress on this car has moved on a bit now.  Body panels have been repaired painted and refitted, the rear electrics have been fitted.  A set of standard lamps had been fitted but as the owner turned 21 our birthday present to him was a set of wipac LED lamps for front and back.  The issue this has now caused is the need to change from a 2 pin flasher relay to a 4 pin set up.

The hope is to have the car rebuilt and in for MOT by the end of November.

IMG_0517.JPG

IMG_0516.JPG

Car 1 : Wiring started

Last week showed yet more progress on the car, the tub was bolted down to the chassis fully, the sides and roof were bolted down to the tub and the inner sills put in place, so the shape of the car is now fixed.  with it being mostly covered we then moved on to other jobs that were needed.

Over the weekend we started to look at the wiring of the car, the autosparks loom is set up on the car and now just needing to find where the connections go to.

So far we have the start system set up so with a key we can turn the engine over, next up will be making sure the warning lamps for the engine work.  When the engine wiring is all done and we are happy we can then progress to fitting the wings and lights.

Car 1 : Update on rebuild

Well here is a long awaited update on the progress of car 1.

In the last update the tub had been painted and the cappings put on, wiring loom threaded in to chassis, brakes completed, steering.

Since this the seatbox has been painted green, bits on it have been detailed in black such as the latches for the seat tops.  The rear body work sections have also been painted green and bolted on to the black roof.  This is now sat on the tub in place ready to be bolted down when we are ready.

IMG_0481.JPG

Plans for this week include getting the inner sills bolted back in place, the seatbox bolted in and the rubbing down and painting of the wings and bonnet.  they will all be fitted once we have the engine wired up and running correctly.

IMG_0489.JPG

We have actually started the engine in the last couple of weeks but it just revved so after a bit of diagnosis we think there is an issue with the webber carb that is fitted, it will be replaced in the next 2 weeks with a zenith copy so we shouldn’t have any more issues there.

 

 

Car 4 : Update on rebuild

Well this is a quick update on progress of car 4’s rebuild, there has been so much done to be documented fully.

Front axles rebuilt fully

Chassis rubbed down, repaired & painted

Front & Rear springs replaced with parabolic springs & new shocks fitted

Bulkhead – stripped, repaired, primed, painted, rebuilt & refitted

Front Grill panel – stripped, repaired, primed, painted and refitted

Engine – refurbished, refitted and running.

New exhaust system fitted

Wings & bonnet have been rubbed down primed, painted and fitted

Hopefully we will get a more detailed update with photos soon.

UPDATE:

Over the weekend we did enough work that the engine now fires up using the key and the car has had a short drive around the garden to give it a little test and move around under the car port.

Most of the front electricals have been sorted now.  Side, Dipped, Main and indicator lamps all work, along with the horn.  so left to wire is the washer pump and heater motor.  A rear chassis loom has also been made and will be plugged in tonight and tested for the rear lights.  The next big step is getting the panels all lined up before they get painted and any holes than need drilling can be put in.

Car 2 : Lighting Upgrade Part 2

Well after the dashboard lighting was improved with LED’s after some issues with the Britpart lamp kit I fitted during the rebuild which included the plastic housings melting on the stop tail lights!

A few weeks ago i purchased Wipac LED lights for the outside of the car, 2 front side lights, 2 stop / tail lights and indicators front and back.  The kit also came with a flasher relay designed for the lower power consumption of the LED’s

The main issue with the lamps were the wiring connections that were for 300tdi + cars so I also purchased adapters to bullet connections.  Also the mounting points were 2 screws on the horizontal centre line of the light.

So I had to drill the body work for the mounting holes then removed the old lights and bolted the new ones in place and connected them up.  

There is one fault with the LED indicators that they only work if wired backwards, they work fine with indicators but the hazard switch currently isn’t working so thats something to look at.