Tag Archives: Land Rover Ninety

Toms Car : More Progress

Well today included more progress on Tom’s car, we have now removed the front end bodywork from the car.  We are now in the process of removing all the other body to chassis fixings and the other connections such as wiring and heater controls.

Hopefully we will be able to make more progress over the rest of the weekend and also taking and uploading some more photos.
image

Next steps will include lifting the body as well as fitting some new parts to replace some of the more… delicate… parts of the car. Updates to follow!

Advertisement

Start of a journey

Well Tuesday 9th June marked the start in our next journey, the delivery of the chassis for the 300tdi 90.

Over coming months we are going to be doing the chassis swap on this car and hopefully documenting it the blog.

Keep an eye out for progress and photos.  The plan for this one might be to lift the body off in one go so we all need to hit the gym a bit.

Daisy Pains

Well another quick update, recently we have had a couple of little issues with Daisy the TD5 90, it all started with a bit of wet weather, when trying to drive the engine warning light came on and throttle response stopped.

After using diagnostics the fault showed up in the computer as Driver Demand, after a bit of looking we thought it was the EGR valve, a bit of inspection showed that it was a bit clogged so we fitted an egr blanking kit.  that seemed to do the trick for a little while.

Then a couple of weeks later the same issue happend again! unimpressed we decided to go to the next possible cause the accelerator pedal, we had purchased one off ebay at the same time as the EGR valve so put it back in and the fault remained the same.

We noticed that the fault was caused when pressing the clutch, so replacement of the switch on the clutch pedal with MSK100050 [MSK500010] seems to have sorted the issues for now.

A long needed update

Well things have been a bit manic recently so updates were last thing on the mind.

But alas here we are April 2015 and here is an update on how things are going.

Ian’s Car – 200tdi 90

Well 12 months since the rebuild finished, its MOT time again.  Car went in for its test Tuesday 7th April.  It failed 😦  The issues were headlights weren’t bright enough, the drivers door wouldn’t open from inside the car.

So all in all not too bad, but the worst item was down as an advisory but actually caused the end of the test.  A UJ in the rear prop had failed to the point where the tester wasn’t willing to carry out deceleration tests.  The prop was unbolted and the UJ’s purchased and replaced.  the prop then bolted back on and boy did it make a difference.

The door not opening was a case of adjustments on the mechanism for the handles just shortened them a bit and opening now much easier.

The headlights were the biggest concern.  As I have high performance bulbs fitted to the car when the tester said they didn’t register on the testing machine.  So reading around the subject points at a burnt out light switch causing poor performance.  The solution is to put a relay feed to the lights.  I purchased a Red Bison Boomslang from Paddockspares for £30 it was a bargain for the entire kit.  I had it fitted in no time and made a massive improvement, its a product I would recommend to anyone.

MOT Retest 18 April 1pm.  Result: Car passed

Jordan’s Series II

Well not much work has been done on the car since November, panels are now painted but not yet fitted to the car.  The accelerator has now been refitted and the car can be driven around.

The main reasons for this is we have been busy working on Jordan’s Discovery 2, which since november has had a number of coolant hoses as it has been loosing coolant and the pressure build up has popped them.  We have now replaced the suspected cause of the coolant loss and so far so good.

Nick’s Discovery

It has been plodding along as normal.  We had a bit of fun while jet washing it ready for MOT when the jet wash smashed the sun roof.  so that has been replaced and the alpine windows have been taken out and covered over.

Matthews Series.

As Matthew has decided he isn’t friends with 2 / 3 of us working on Land Rovers there will be no further updates about his car as we dont see him any more.

New Cars:

Yes we have been joined by two more land rovers that we can enjoy working on.

Daisy The Defender is a 2006 TD5 90, owned by some friends we have had a little bit of work to do on the car already including replacing a failed fuel pump and then adding some new bits such as chequer plate wing tops and a new bumper.  With being such a new car there shouldnt be that much to do on it for now.

Tom’s 300tdi 90, this is going to be our next big project, Toms car is in need of a new chassis, due to the amount of rust it has, we could go down the route of repair pieces but Tom fancies doing a chassis, so one has been ordered so big project ahead for the summer.  There should be plenty of updates on this one.

Car 2 : Lighting Upgrade Part 2

Well after the dashboard lighting was improved with LED’s after some issues with the Britpart lamp kit I fitted during the rebuild which included the plastic housings melting on the stop tail lights!

A few weeks ago i purchased Wipac LED lights for the outside of the car, 2 front side lights, 2 stop / tail lights and indicators front and back.  The kit also came with a flasher relay designed for the lower power consumption of the LED’s

The main issue with the lamps were the wiring connections that were for 300tdi + cars so I also purchased adapters to bullet connections.  Also the mounting points were 2 screws on the horizontal centre line of the light.

So I had to drill the body work for the mounting holes then removed the old lights and bolted the new ones in place and connected them up.  

There is one fault with the LED indicators that they only work if wired backwards, they work fine with indicators but the hazard switch currently isn’t working so thats something to look at.